Buyer Guide
Home Inspection Checklist
A room-by-room home inspection checklist for buyers: what inspectors check, typical costs, specialty add-ons, and how to turn findings into savings.
Home Inspection Checklist
A home inspection costs a few hundred dollars and routinely surfaces problems that cost tens of thousands to fix. It is the best ratio of money spent to risk avoided anywhere in the buying process, and the findings become leverage: repair requests, price credits, or a clean exit before closing.
Most buyers attend the last twenty minutes, skim the report, and move on. A better approach is to know what the inspector is checking, walk the house with the same checklist in hand, and use the report deliberately during your contingency window.
What a Standard Inspection Covers and What It Costs
A standard inspection is a visual, non-invasive review of the home's major systems: roof, structure, electrical, plumbing, heating and cooling, insulation, and the exterior. The inspector does not open walls or move the seller's belongings, which is why some problems stay hidden even after a thorough visit.
Expect to pay about $300 to $600 for a typical single-family home, and $500 to $900 for larger or older houses. The visit usually runs two to four hours, and the written report with photos arrives within a day or two.
The report will flag dozens of items in almost any house, including new ones. Your job is sorting the handful of expensive or dangerous findings from the routine maintenance list, and the checklist below is organized around where the expensive findings hide.
The Checklist, System by System
Walk the house in the same order the inspector does and the big-ticket systems get covered first. Roof, structure, electrical, plumbing, and HVAC account for most of the repair dollars in a typical report.
Use these sections during your own showings too. Spotting a red flag before you write an offer is cheaper than discovering it during the contingency period.
Roof and Attic
Ask the age of the roof first, since asphalt shingles last roughly 20 to 30 years and replacement on an average home runs about $10,000 to $25,000. From the ground, look for curling shingles, patched sections, and sagging lines along the ridge.
In the attic, the inspector checks for daylight through the sheathing, water stains, mold on the underside of the roof deck, and whether ventilation and insulation suit the climate. Insulation depth matters, and many older homes carry half of what current standards call for.
Foundation and Structure
Hairline vertical cracks in poured concrete are common and usually cosmetic. Horizontal cracks, stair-step cracks in block walls, and any crack wider than about a quarter inch deserve a structural engineer's opinion, which typically costs $400 to $800.
Inside, sloping floors, doors that stick or swing on their own, and drywall cracks radiating from window corners all hint at movement. One symptom alone is rarely alarming, while a cluster of them is worth the engineer's visit.
Electrical Panel and Wiring
The panel tells the story fast. The inspector checks for:
- Adequate service, with 200 amps now standard for most homes
- Panel brands with known failure histories that insurers flag for replacement
- Double-tapped breakers and amateur wiring inside the panel
- GFCI protection in kitchens, bathrooms, garages, and outdoor outlets
- Aluminum branch wiring in homes built in the late 1960s and early 1970s
Knob-and-tube wiring in pre-1950 homes and aluminum branch circuits both raise insurance questions and can cost $8,000 to $20,000 to remediate. Get a licensed electrician's quote before closing if either shows up.
Plumbing and Water Heater
Water heaters last about 8 to 12 years, and the manufacture date is printed on the data plate, so check it. Replacement runs roughly $1,200 to $3,500 for a standard tank, more for a tankless conversion.
Run water in every fixture and watch pressure and drainage. The inspector also identifies supply pipe materials, since certain 1980s plastic supply lines and the galvanized steel in older homes are both prone to failure, and a full repipe can reach $5,000 to $15,000.
HVAC Age and Function
Furnaces last about 15 to 20 years and central air conditioners about 10 to 15, and replacing a full system commonly runs $8,000 to $20,000. The inspector runs both heating and cooling and measures the temperature difference across the system.
Ask when the equipment was last serviced and look at the filter yourself. A clogged filter and dirty coils suggest the same neglect probably extends to everything else mechanical in the house.
Windows, Doors, and Insulation
Fogged double-pane windows mean failed seals, and while one window is minor, a houseful of failed units can run $500 to $1,200 each to replace. Open and close a sample of windows and exterior doors on every floor.
Check weatherstripping, caulking, and how rooms farthest from the thermostat feel. Uneven temperatures usually trace back to insulation gaps or duct problems rather than the furnace itself.
Exterior Grading and Drainage
Soil should slope away from the foundation, roughly six inches of drop across the first ten feet. Outside, the inspector looks for:
- Downspouts that dump beside the foundation instead of several feet away
- Ponding, erosion channels, or mulch piled against the siding
- Rotted trim, failing paint, and gaps where water or pests can enter
- Deck ledger boards bolted, rather than nailed, to the house
Water moving toward the house causes a large share of basement and crawlspace problems. Fixing grading early is cheap compared with waterproofing later, which can run $5,000 to $20,000.
Appliances
Inspectors run the dishwasher, range, oven, disposal, and often the laundry machines through a basic cycle. Note the age of each, since most major appliances last about 10 to 15 years and a full kitchen's worth costs $5,000 to $15,000 to replace.
Built-ins matter more than freestanding units because they convey with the house and cost more to swap. Confirm in the contract which appliances stay.
What Inspectors Do Not Cover
A standard inspection excludes anything hidden or anything that needs specialized equipment. The inside of walls, the sewer lateral, chimney flues, wells, and whatever sits under furniture or insulation all fall outside the scope, and inspectors say so plainly in their contracts.
Specialty add-ons fill those gaps for a fee. A sewer scope runs about $150 to $350 and is worth ordering on any home more than 25 years old, since a collapsed lateral costs $5,000 to $25,000 to replace. Radon testing runs about $150 to $250, termite inspections $75 to $150, mold testing $300 to $600, and a pool inspection $200 to $400.
Order add-ons based on the house and the region. A 1960s house with mature trees over the sewer line and a basement in a radon-prone area deserves both tests, while a five-year-old slab home in the same market may need neither.
Turning Findings Into Repairs, Credits, or a Walk-Away
Prioritize safety issues, structural problems, and active water intrusion. Those categories are worth negotiating, while cosmetic items and routine maintenance requests mostly annoy sellers and weaken your position on the things that matter.
You generally have three moves: ask the seller to repair before closing, ask for a credit or price reduction, or walk away. Credits are often cleaner than seller repairs, since you control the contractor and the quality instead of accepting the cheapest fix the seller could find.
Deadlines rule everything here. Your contract's inspection contingency, called the option period in some states, typically gives you about 7 to 10 days to inspect, negotiate, and either proceed or exit with your earnest money, and missing that window can forfeit your leverage entirely.
Attend the Inspection and Ask Questions
Show up for at least the final hour. The inspector will walk you through the house, point at what the report will describe, and give you an unwritten sense of severity that a PDF cannot convey.
Ask which finding the inspector would fix first, which items are routine maintenance rather than defects, and where the water, gas, and electrical shutoffs sit. The answers shape your negotiation list and your first month of ownership.
Photograph the data plates on the furnace, water heater, and any roof paperwork the seller left behind. Those ages feed directly into your five-year budget, and for the rest of the purchase process, our other guides for home buyers pick up where the inspection ends.
Frequently Asked Questions
How much does a home inspection cost?
Most single-family inspections run $300 to $600, with large or older homes reaching $900. Add-ons like a sewer scope or radon test add $150 to $350 each.
Can a house fail a home inspection?
No, inspections have no pass or fail grade. They produce a report of conditions, and a typical report lists 20 to 50 items ranging from trivial to serious.
Should I inspect a brand-new house?
Yes. New-construction inspections regularly find unconnected ducts, missing insulation, and plumbing errors, and many buyers also pay $300 to $500 for a pre-drywall inspection during the build.
What if the seller refuses to make repairs?
You can accept the house as is, ask for a credit instead, or exit within your contingency window and keep your earnest money. A credit of even $5,000 to $10,000 often beats rushed seller repairs.
How long does an inspection take?
Plan on two to four hours for an average home, longer for large or older properties. The written report with photos usually arrives within 24 to 48 hours.